Re: Lob segment Reorganization failure
Dear Roman, Please find the attached files with both outputs... RegardsImaan
View ArticleRe: Lob segment Reorganization failure
Dear Reagan, Thanks for the information : 1-> Our brtools was recently upgraded to BRTOOLS 7.20 (33) with kernel 720 Ext.2-> I have already executed the reorg reports as per SDN -...
View ArticleRe: Lob segment Reorganization failure
Hi, Take a look at the below blog:http://scn.sap.com/docs/DOC-43948 Regards,Nick Loy
View ArticleRe: upgrade to 11g from 10.2.0.5 instead of from 10.2.0.4
Hi Junior,Prerequisites:In the following special cases you need to obtain more information:—If you are upgrading from Oracle 10.2 to Oracle Database 11g Release 2 (11.2) in manual mode (in this guide...
View ArticleRe: Lob segment Reorganization failure
You have only ~23GB of free space in tablespace, but at the same time ~69GB of LOB data in table SOFFCONT1. You need to add space to tablespace.
View ArticleRe: Shrink versus tradicional reorganization with brtools
Hi Stefan, and thanks for your deeply explanation. So, I understand that there are no problems to run shrink in a production system in any time. Regards.
View ArticleRe: Shrink versus tradicional reorganization with brtools
Hi Maximino,well i did not say this .. i said "The basic effect to the sessions is like described, but the explanation is not correct.". The "shrink space" DDL is an online operation (lock mode 3)...
View ArticleClik here to view.
Re: [Architecture] Question about performance - SAP + Oracle on Linux (single...
Hello Stefen, thank you for a lot of information. They are helpful - most of them for the people who without broader experience in sizing. Your information is out of the topic in relation to...
View ArticleRe: Shrink versus tradicional reorganization with brtools
Stefan Koehler wrote: The "shrink space" DDL is an online operation (lock mode 3) until the end when the lock is converted (not escalated - that is the critical point here) to mode 6.What is the...
View ArticleClik here to view.
Re: Shrink versus tradicional reorganization with brtools
Hi Roman, > What is the difference (technical implementation "under the hood" from Oracle) between lock conversion and escalation?Oracle itself does not use / need lock escalation, so the only...
View ArticleRe: Shrink versus tradicional reorganization with brtools
Hi Stefan, thanks for your reply. Kind regards,Roman
View ArticleUrjent!! disp+work.EXE not working.
Urjent!! PFA dev_w0 log for analysis.Due to power failure, SAP server got rebooted.After starting DB, when tried to start SAP disp+work.EXE is not running.dev_w0 log id attached for reference.
View ArticleRe: Urjent!! disp+work.EXE not working.
Hi There are no major error in the log file except one for SSO that should not prevent the instance from starting.The Kerberos Service Principal Names for (p:SAPServiceCHQ@xxx.yyy.COM) cannot be...
View ArticleRe: Urjent!! disp+work.EXE not working.
Kindly let me know how to bypass this issue?Thank you for quick reply.
View ArticleRe: Urjent!! disp+work.EXE not working.
Either you start the active directoryYou can try to set these parameters that should allow non SSO/SNC access.snc/accept_insecure_cpic =1snc/accept_insecure_gui = 1snc/accept_insecure_r3int_rfc...
View ArticleSAP Backup with Symantac backupexe 2010
Dear Friend, How can I configure oracle backup with Symantac backupexe 2010. Regards,Krishna,
View ArticleRe: SAP Backup with Symantac backupexe 2010
Hi Krishna Kindly refer the Symantec backup exec link http://www.symantec.com/connect/forums/symantec-backup-exec-2010-oracle-agent RegardsRam
View ArticleRe: SAP Backup with Symantac backupexe 2010
Hi,check below URLs, hope they will help you:...
View ArticleRe: SAP Backup with Symantac backupexe 2010
Hi, Please navigate with below: Symantec Backup Exec Server 2010 - Configuring On Windows Server 2008 R2 - Part 1 - YouTube http://www.symantec.com/connect/blogs/betc-be2010-free-modules Install and...
View ArticleRe: Oracle parameters
I'm a bit confused. Then If I the parameter doesn't appear in initSID.ora then is not active in the current DB? Then Doesn't matter that the parameter exists with its default value?
View Article